Jump to content

rejaorac

Members+
  • Content Count

    2
  • Joined

  • Last visited

Community Reputation

0 Neutral

About rejaorac

  • Rank
    RC-Cam Visitor
  • Birthday 06/26/1966

Contact Methods

  • MSN
    rejaorac@gmail.com
  • Skype
    rejao66

Profile Information

  • Location
    carapicuiba SP BR
  1. sou brasileiro fanatico por heli modelismo sou navato na aria de helimodelismo tenho poco conhecimento na aria de eletronica essa ateração do receptor r 617fs acima postada por mim me gero uam duvida sera que ar posabilidade de funciona o esquema dessa alteração para o treinir sei fio se tiver auguei que possa avaliar as diferencia entre o WTR-7 FASST e essa alteração o problema e que um e in entrada ppm e o otro e out saida ppm por vafavor essa possabida de usa essi sistema comu treini sem fio tenho gande sartifação de fazer pate deste forum obrigado a todos que compatilha estas maravilha da eletronica com nosco valeu todos?????? 'm Brazilian fanatico by heli modeling navato am in aria of helimodelismo poco have knowledge in this aria of electronic ateração receiver r 617fs above posted by me me gero uam doubt that air will be posabilidade works of this scheme amendment for the wire if you know treinir auguei that can evaluate the difference between the WTR-7 FASST and this change the problem and that an entry ppm and in and out of each other and the ppm output for this vafavor possabida of essi system uses wireless commu treini have gande sartifação making pate this forum thanks to everyone who compatilha these electronic marvel with Nosco earned all???
  2. hello all forum rc agradesso to be part of this forum I use ese receptor changed in a simulated funsiona pefeito wireless so I entedir the bus fuciona s the same way and that Step by Step Walkthrough Please read the whole process before start! To exclude the possibity that your receiver is dead on arrival (DOA), you should first connect a regular RC servo and power supply to check that it is working correctly. Step 1: Open the case The case consists of a bottom and top part. They are connected by four notches snapping into the corresponding cutouts on the lower case. Take care of electrostatic discharge (ESD) risks by tapping a radiator or other metallic grounded object (personal computers are grounded) before opening the case. Best practice is to use an ESD arm strap, if available. Push the notches back with a small screw driver (blade width of 2.5 mm fits perfectly) and at the same time gently apply pressure to move the two parts away from each other. Watch out to not pull on the antenna wires, you can remove the rubber tubes holding them to the plastic case. Step 2: Remove Resistor connecting Plug Depending if all seven channels should still be usable, two options exist: You can connect the sum signal to an additional header, which you should fix tightly, e.g. by hot glue, or you disconnect the servo signal on one channel and connect the sum signal to this header. This tutorial will proceed by disconnecting channel 7, as this channel is not usable with the six channel T6EX transmitter. Desolder now the resistor in front of the header for channel 7. In theory you can undo the modification by removing the cable (later step) and re-adding this resistor. The receiver is build in a lead-free ROHS process. The melting temperature is therefore higher than with usual solder. We had to ramp up the soldering iron to 370° C (700°F) to melt the solder. Apply heat to both sides of the resistor until you can gently slide it off its position. Step 3: Connect PPM Sum Signal This step connects the sum signal to the freed header. You need a very tiny cable. Remove the insulation by 0.5 - 0.8 mm (0.3”). Apply solder flux to both ends and cover them with plenty of solder. Place one end on one of the two marked pins (it is easier on the left IC, as you have additional space on the edge) and solder it to the pin. Make sure that is is connected right by gently pulling on the cable. Place the other end on the signal pin (see photo) on the header and solder it. Step 4: Check Check for remaining solder on the PCB or bridged pins. It might be a good idea to secure the sum signal cable against vibrations by hot glue or epoxy. If you have an oscilloscope at hand, you should get five signals of about 1 ms, 20 ms break and the same again. The PCB should now look like the photo. Step 5: Close the case You can easily add the case by placing the pcb inside and snapping the notches back into the bottom part. Your receiver now looks exactly the same. It might be a good idea to mark port 7 as sum-signal out.
×
×
  • Create New...