Jump to content

Attention: RC-CAM.com will be closing down August 2021.

The RC-Cam.com forum was the very first online community dedicated to the advancement of wireless video cameras on radio controlled (R/C) models. This is now called "FPV" (First Person View). We are proud of the contributions that our members have made to the FPV hobby.

We've seen significant changes over the last twenty years. Initially there were a lot of eager R/C hobbyist that built their own video systems. Allowing these creative individuals to share their work was the purpose of this site. Now the FPV market is flooded with low cost systems; Sadly DiY FPV video projects are now rarely discussed.

RC-CAM.com (main site and forum) will be closing down August 2021. This is being announced now (March 2021) so that everyone has time to download any information that is important to them. After the site is shutdown the information will no longer be available here.

We appreciate every member's involvement with advancing the FPV hobby. It is indeed sad to say goodbye to all our online friends. Be safe and stay healthy.



Recommended Posts

I think you will find that the buzzers that do not work with LoMA are simply the wrong type. Many 1205 type buzzers are missing the required internal drive oscillator (the buzzer you use must have an internal 4VDC-5VDC oscillator drive circuit). To test this, connect your buzzer directly to a 4.5V power source and verify you hear the loud buzzer tone. Also, measure the current to see that it is under 40mA. If these conditions are OK then it should work with LoMA.

Link to post
Share on other sites
  • 2 weeks later...

Hi Folks..

I'm having a bit of a problem with buzzers as well. I bought the following but for some reason, they don't seem to work until I discovered that the buzzers seem to be external drives:

http://www.maplin.co.uk/5vp-p-pcb-piezo-transducer-98112

I've tried sourcing others but can't quite put my hands on any. Off to have another hoke(look) but if anyone can shed light this side of pond I'd be grateful.

Regards

Declan

Link to post
Share on other sites

I've noticed that if the part's catalog description only mentions "piezo transducer" then it usually requires an external drive. The ones with internal drives (which LoMA requires) usually mentions "buzzer" or "built-in oscillator" in their description. No doubt there are exceptions, so simply review the data sheet -- it will tell all the details.

No experience with it, but maybe this one will work:

http://www.maplin.co...indicator-98109

Edited by Mr.RC-Cam
Added maplin part number
Link to post
Share on other sites

I've noticed that if the part's catalog description only mentions "piezo transducer" then it usually requires an external drive. The ones with internal drives (which LoMA requires) usually mentions "buzzer" or "built-in oscillator" in their description. No doubt there are exceptions, so simply review the data sheet -- it will tell all the details.

No experience with it, but maybe this one will work:

http://www.maplin.co...indicator-98109

Cheers. Many thanks

Just ordered some up. Don't know how I missed that one!!

Declan

Link to post
Share on other sites
  • 1 month later...
  • 9 months later...

Thanks for your prompt reply.

Another question.

I have this buzzer with the following specs;

Oscillation Frequency (Hz) 3000 ± 500

Operating Voltage (Vdc) 1.5 ~ 30

Rated Voltage (Vdc) 12

Current Consumption (mA/max) 12 at Rated Voltage

Sound Pressure Level (dB/min) 80 at 30cm at Rated Voltage

My question is, I will use this LMA in a Plank and my battery pack is aroung 6V.

In my understand, I need to get 12V to have the louder db (as rated voltage) Is there a way to double my battery pack voltage (6v) to have a louder noise ?

Link to post
Share on other sites
Operating Voltage (Vdc) 1.5 ~ 30

This tells me it is a piezo sounder and not a buzzer. The item you have requires an oscillator driver circuit whereas the one spec'd for the project will make noise simply by applying 5VDC to it.

Also, the PIC will be damaged by 6V so you need to add a 5V Voltage Regulator to the LoMA. Or perhaps drop the power supply voltage with a couple of series diodes in the Vcc supply.

But to answer your question, if you want to operate the buzzer on a voltage higher than 5V then you will need to add a transistor stage to drive it. I'll leave that part up to you.

Link to post
Share on other sites
Check the link of the a buzzer a have

I don't have any experience with it so I can't say if it is a good choice. If it has an internal oscillator, works on 5V, and requires less than 40mA, then it should be fine.

FWIW, I have found that high frequency alert tones are not good choices for a lost model alarm. The higher frequency tones are often too directional and attenuate too quickly for this application. So try to select one that has the lowest possible audio tone frequency and highest sound pressure spec. The buzzer recommended in the project (http://products.cui....pdf?fileID=8247) works fine using ~2.3KHz and is quite loud). I don't recommend anything with a frequency that is much higher than that.

I have read the some diodes can do that, Do you agree ?

Diodes can be used to drop the power supply voltage. Be sure that the PIC never sees more than about 5.25V with a fully charged pack.

Link to post
Share on other sites

Suddenly I found one buzzer in a old fax modem card (pci) I had.

dsc05810qd.jpg

Only thing I am in doubt, I applied power over the buzzer terminals and I could not hear a sound. Does it need the PIC in order to produce the frequencies or it should do a noise without the PIC ?

Edited by chrispaiva
Link to post
Share on other sites

You must use a Buzzer with built in oscillator; The PIC does NOT provide the audio frequency. The correct buzzer choice for this project will be the type that makes the noise as soon as you apply 5VDC.

Link to post
Share on other sites

Tomas,

I have finished my loma and it worked ! So happy ! :-P

Thanks for sharing your projects, I think this is the way to have knowledge spread around the world. You could help me miles away from your home. This is fantastic.

I am using a Turnigy 2.4 with Frsky Receivers. I could add the loma start using a switch perfectly setting the ATV from 0% to 125% after test I should have read the part to disable the glitch counter once I want to start noise from the switch.

My real problem now is to have the properly buzzer in hands, i did a search in the eletronics stores (a few) in my city, but I can only find piezzo buzzer. They do not sound loud.

In my previous post I sent a image of a magnetic buzzer took from a modem card.

Do you know a way to design a oscillator to feed this buzzer ?

I googled without sucess

Buzzer´s Specs

PAC-WT-1205-P

Rated Voltage 5

Drain Max.40mA

Coil Resistence 47±5ohm

dB - Min.87

Resonance 2400±200Hz

Operating Voltage 4-6V

Operating Temperature -20~+60

Weight(g) 2

Dimensions Ø12 x 9.8

Thanks in advanced !

Link to post
Share on other sites
  • 3 years later...

This is an old project that was developed for FM PPM receivers that do not output a valid servo pulse when the RF signal is lost.

Unfortunately your FrSky receiver has failsafe detection built into it. The FrSky is designed to produce artificial servo signals when RF control is lost. So it is not compatible with my published design.

The green LED on your receiver turns off when the RF signal is lost. Maybe you can create a circuit that monitors the green LED drive signal and have it control a buzzer. I don't have any details on how to do that, so it will need to be your own DiY project.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...